日本針對無線電射頻設備的認證稱為Radio Equipment Type Approval，管控機構是日本總務省MIC(Ministry of Internal Affairs and Communications)，主要認證機構是由MIC指定的TELEC(Telecom Engineering Center)，還有如RF Technologies/JQA/SGS/ITS/TUV/UL等共12家出證機構，所以通常又稱為TELEC認證，也有人稱為MIC認證、RF認證、GITEKI認證、技適認證，類似國內的SRRC認證。

       藍牙和WIFI產品TELEC認證測試要求

       測試認證是針對每一個設備單元進行驗證，該認證只對每一個經過了驗證的設備單元有效; WiFi和Bluetooth產品其的測試項目基本上與歐標的EN300 328類似. 其中2.4GHz WiFi產品(802.11b/g，2412~2472 MHz)和Bluetooth產品使用的標準為MIC Notice No.88 Annex43，但是對于2.4GHz WiFi產品的14信道(Channel 14：2471 ~ 2497MHz)則需要單獨使用Annex44進行測試和出具報告，相應的規費也需要增加。 對于5GHz WiFi產品(802.11a，5180~5320MHz，W52 Band和W53 Band)遵循的測試標準為Annex45，但是需要注意的是，資料顯示，MIC近期將會修改Annex45，將5.6GHz設備(Band W56)也歸入Annex45，并且對Band 56頻段有更加嚴格的DFS測試要求。

       藍牙產品TELEC認證測試內容

       1、頻率誤差測試(Frequency Error Measurement)

       2、耦合帶寬/載頻帶寬測試(Occupied Bandwidth and Spread-spectrum Bandwidth / Factor)

       3、雜散擾測試(Unwanted Emission Intensity Measurement)

       4、天線功率誤差測試(Antenna Power Error Measurement)

       5、接收機雜散擾測試(Limitation of Collateral Emission of Receiver Measurement)

       6、EIRP天線功率測試(Transmission Antenna Gain (EIRP Antenna Power) Measurement)

       7、3dB波瓣帶寬測試(Transmission Radiation Angle Width (3dB Beamwidth) Measurement)

       8、占空比測試(Duty Cycle Measurement)

       9、占用時間測試(retention time)

       藍牙和WIFI產品TELEC認證需要提交的資料

       (1)技術型號規格表(Technical Type Specification Form)

       (2)質量申明管理系統(Declaration of Quality Management System)

       (3)質量證書的控制批準方法或者ISO9001證書(Letter of Quality Control Confirmation MethodorManufacturer’s ISO 9001 Certificate)

       (4)結構保護批準證書(Letter of Construction Protection Confirmation)

       (5)宣稱的額定功率(Rated Power Declaration)

       (6)天線報告(Antenna Report)

       (7)測試報告(Test Reports (including Test Results, Test Setup Photos and Examinations carried out))

       (8)(Block Diagram, Schematic Diagram, Bill of Material, Parts Placement, IC Data Sheets, Internal and External Photos, Product Description, User manual, Operational/Technical Description, Description of Pheripherals/Accessories)

       (9)標簽信息(Label Information(Label Location, Label content))

       If you act as agentoras authorized representative of the manufacturer:

       (10)委托書/授權書(Power of Attorney / Authorization Letter)